• Service & Repair
  • Hot Tubs for SaleCOMING SOON
  • Shop By Hot Tub Brand
  • Shop By Parts Brand
  • Our blog
  • Contact us

Smaller Pump Parts

Smaller Pump Parts

Welcome to the Small Pump Parts section of our store.

Here you will find all the smaller hot tub pump components for pump brands such as Waterway, Aqua-flo & ITT Hydroair. Small parts such as wet end wear rings, O rings, faceplate screws, drain plugs, and many others.

If you require any help with finding a particular pump part then you can contact us here, we will be more than happy to assist you.

58 item(s)
HTP287

1.5" union O' rings, fits unions used with Waterway & Aqua-flo pumps. Can be used with some spa heaters.

£126 (£105 Ex. VAT)
+
3 item(s)
HTP268
  Manufacturer  - Waterway Plastics Part Number  - 311-1220 Type of Product  - Pump Wet End Faceplate Diameter (OD)  - 190mm (Excluding fixing mouldings) Union Size - 2-inch (78mm Thread OD)  
£4513 (£3761 Ex. VAT)
+
434 item(s)
HTP1461

2" pump union seal - This is the flat type and because they are flat they will fit all 2" pump unions.

£176 (£147 Ex. VAT)
+
190 item(s)
HTP284

2" union O' rings, fits unions used with Waterway & Aqua-flo pumps. Can be used with some spa heaters.

£151 (£126 Ex. VAT)
+
3 item(s)
HTP269
  Manufacturer  - Waterway Plastics Part Number  - 311-1210 Type of Product  - Pump Wet End Faceplate Diameter (OD)  - 190mm (Excluding fixing mouldings) Union Size - 2.5-inch (93mm Thread OD)  
£4237 (£3531 Ex. VAT)
+
2.5" Pump Union O' Ring (Single) -5%
64 item(s)
HTP434

2.5" pump union O' ring, fits the larger 2.5" suctions on Waterway pump wet ends.

£151 (£126 Ex. VAT) £132
+
1 item(s)
HTP346-1

Rubber mounting feet for 48frame Waterway/EMG pumps - Sold in pairs

£509 (£424 Ex. VAT)
+
HTP346

Rubber mounting feet for 56frame Waterway/EMG pumps - Sold in pairs

£509 (£424 Ex. VAT)
215 item(s)
HTP240
  Manufacturer  - Waterway Plastics Part Number  - 805-0115 Type of Product  - Air Bleed O' Ring Dimensions (MM) - Diameter:  15mm OD
£114 (£095 Ex. VAT)
+
112 item(s)
HTP579
  Manufacturer  - Aqua-flo Part Number  - 92830070 Type of Product  - Pump Impeller Wear Ring Used with Impeller HP  - 1/2/3hp Outer Diameter   - 64mm Internal Diameter  - 54mm
£482 (£402 Ex. VAT)
+
15 item(s)
HTP2841
  Manufacturer  - Aqua-flo Part Number  - 92830080 Type of Product  - Pump Impeller Wear Ring Outer Diameter   - 71mm Internal Diameter  - 61mm
£482 (£402 Ex. VAT)
+
30 item(s)
HTP1304
  Product Specifications Manufacturer  - LX Pump Co. Part Number  - PL-10088 Type of Product  - Pump Wet End Air Bleed Screw Dimensions (MM) -  Length:  19mm,  Width:  18mm (Thread 12mm)  
£186 (£155 Ex. VAT)
+
147 item(s)
HTP406

3/8 Pump air bleed nipple - found threaded into pump wet ends and always snap of at the thread when replacing pumps.

£329 (£274 Ex. VAT)
+
HTP1645
Self Air Bleed Nipple, LX Pumps Genuine replacement self-air bleed nipple complete with O' ring used on many LX spa pumps, all WP & LP models & others. Threads into one of the bleed screw ports on an LX pump faceplate volute, allowing any air trapped within the wet end to self bleed into the spas venturi system and saving having to manually bleed the LX pump. Works Well With Used on LX pumps, LP200, LP250, LP300, WP200, WP250, WP300 & LX Circulation pumps. Only fits LX Hot Tub Pumps. Product Specifications Manufacturer  - LX Pump Co. Part Number...
£186 (£155 Ex. VAT)
18 item(s)
HTP258

Volute O Rings - Fit all Waterway Executive Pump Wet Ends

£890 (£742 Ex. VAT)
+
1202 item(s)
HTP1168
Wet End Bolts x4 - 48 Frame 4 x 48 Frame wet end bolts used to bolt EMG motors to pump wet ends. You will need these bolts when replacing an American motor for a EMG motor and keeping your original wet end. The reason you will need them is that most American pumps have long bolts that go right through the motor from the rear to the wet end and will be of no use when bolting a EMG motor onto your wet end.
£328 (£273 Ex. VAT)
+
386 item(s)
HTP1167
Wet End Bolts x4 - 56 Frame 4 x 56 Frame wet end bolts used to bolt EMG motors to pump wet ends. You will need these bolts when replacing an American motor for a EMG motor and keeping your original wet end. The reason you will need them is that most American pumps have long bolts that go right through the motor from the rear to the wet end and will be of no use when bolting a EMG motor onto your wet end.
£328 (£273 Ex. VAT)
+